Ibm T221 Manual do Utilizador

T221 Flat-Panel Monitor User’s Guide

4Storing the connector tool This section describes how to store the connector tool for future use. This tool will be useful when disconnecting the c

Chapter 2. Hardware setup 53. Remove the connector cover. 4. Unhook the digital signal cable from the cable hook and lift it

6Connecting the cables This section describes how to connect the following cables: 1. Power adapter cord 2. Digital signal cable 3. Power cord Conn

Chapter 2. Hardware setup 73. Reinstall the connector cover on the monitor. 4. Reinstall the stand rear cover and turn the

8Connecting the digital signal cable Note: If you use the converter box, see “Converter Box User s Guide”. 1. Make sure that the power cord is NOT

Chapter 2. Hardware setup 9Connecting the power cord Note: Read the respective Danger Statements on pages iii through xiii before continuing wit

104. Press the power switch on the monitor. The power light comes on. Notes: a. When you turn off the monitor, wait at least fiv

Chapter 3. Adjusting and maintaining your monitor 11Chapter 3. Adjusting and maintaining your monitor This chapter describes the following: How

12Setting the monitor control buttons You can control the various functions of the monitor using the buttons at the front right of the monitor.

Chapter 3. Adjusting and maintaining your monitor 13Accessing the on-screen display (OSD) menus You can access the on-screen display (OSD) menus

ii Second Edition (July 2003) The following paragraph does not apply to the United Kingdom or any country where

14Submenus To access a submenu, do the following: Brightness submenu 1. Select the Brightness icon on the Main menu using the Left-Arrow or the

Chapter 3. Adjusting and maintaining your monitor 153. Press the Left-Arrow button for at least 3 seconds to disable or enable the color managem

16Checking the operating status of your monitor You can check the status of your monitor by the color of the power light. The col

Chapter 3. Adjusting and maintaining your monitor 17Disconnecting the cables Note: Before you begin the procedures below, be sure to read the Da

18Using the security keylock The monitor has a built-in security keyhole at the rear of the screen for fastening a security lock and cable. This lock

Chapter 4. Troubleshooting 19Chapter 4. Troubleshooting If you suspect something is not working correctly, you should: 1. Turn on the computer

20Appendix A. Specifications The specifications of the monitor are as follows: Maximum addressability Horizontal: Vertical: 3840 pixels 2400 pixels

Appendix A. Specifications 21Recommended configuration The following pages contain comprehensive details of the T221’s capability and attachment

22Supported display modes All versions of the monitor support the following modes. 1) Industry & standard modes Addressability DVI Input Horiz

Appendix A. Specifications 23Addressability (QUXGA-W) DVI Input H Freq. (kHz) V Freq.(Hz)Pixel Clock (MHz)EDID** (960x2400)x4 ch1 ~ 4 99.2 40.9

Notices iiiNotices Attention • Do not exert strong pressure to the surface of the monitor screen. You may break the LCD panel. • Do not place hea

24Notes: * Requires dual-link DVI converter box **Each EDID contains up to four extended timings, the number (P1 - P4) in the top section of the tabl

Appendix B. Updating the settings for your monitor 25Appendix B. Updating the settings for your monitor Introduction Modern monitors internally

262. Enabling the special OSD (on-screen display) menu a. Press the leftmost OSD button (select / enter) and navigate to the (i) (information) icon

Appendix B. Updating the settings for your monitor 27using the 'select / enter' button. The brightness range will now extend from 0 to

28 EDID setting numbers and DDC-CPU versions Version of DDC- CPU EDID number 3.2 3.3 3.4 3.5 3.6 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.

Appendix C. Configuring your video graphics card 29Appendix C. Configuring your video graphics card There are several aspects of video graphics

30Appendix D. Field Replaceable Units (FRUs) No FRU FRU part number Part number (IBM 9503-DG3) 55P5067 07N2209 1 Monitor (IBM 9503-

Appendix E. Compliance 31Appendix E. Compliance TCO’95 Congratulations! You have just purchased a TCO'95 approved and labelled pro

32display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to rea

Appendix E. Compliance 33Mercury** Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic

ivIBM may have patents or pending patent applications covering subject matter in this document. The furnishing of this document does not give you any

34Deutsche EMV-Direktive (electromagnetische Verträglichkeit) Dieses Gerät ist berechtigt in Übereinstimmung mit dem deutschen EMVG vom 9.Nov.92 das

Appendix E. Compliance 35Avertissement: Ceci est un produit de Classe A. Dans un contexte résidentiel ce produit peut causer une interférence rad

36Statements for Other Countries Power Cord For your safety, IBM provides a power cord with a grounded attachment plug to use with

Appendix E. Compliance 37 MPRII This product complies with Swedish National Council for Metrology (MPR) standards issued in December 1999 (MPRII)

Contents vContents NOTICES ...

viAPPENDIX D. FIELD REPLACEABLE UNITS (FRUS)... 30 APPENDIX E. COMPLIANCE ...

Chapter 1. Before setting up 1Chapter 1. Before setting up This guide contains information on how to set up and operate the IBMTM 9503 T221 Flat

2Checking parts Check the box for the following items. If any items are missing or damaged, contact your place of purchase immediately. Monitor

Chapter 2. Hardware setup 3Chapter 2. Hardware setup This chapter describes the following: The location of the controls, switches, and connectors