IBM M/02-212 Manual do Utilizador

Brookfield Engineering Labs., Inc. Page 1 M/02-212 BROOKFIELD R/S RHEOMETER Operating Instructions Manual No. M/02-212

Brookfield Engineering Labs., Inc. Page 10 M/02-212 III.2 Electrical Connections Connections for the electrical components of the R/S Rheomete

Brookfield Engineering Labs., Inc. Page 11 M/02-212 III.2.2 AC-Adaptor The AC adaptor supplies R/S Rheometer with power. Only the AC-adaptor

Brookfield Engineering Labs., Inc. Page 12 M/02-212 Please read information concerning installation of the computer system in this Operation Ma

Brookfield Engineering Labs., Inc. Page 13 M/02-212 OKSTPowerMain-Menue - Run Single - Run Program - RemoteBROOKFIELDCooling device KETemperatu

Brookfield Engineering Labs., Inc. Page 14 M/02-212 -20 °C to +250 °C thermostat oil Thermostatic fluids can be ordered from BROOKFIELD. Dur

Brookfield Engineering Labs., Inc. Page 15 M/02-212 During measurements in the temperature range below -10°C and above +90°C the measuring de

Brookfield Engineering Labs., Inc. Page 16 M/02-212 Measuring device for cone/plate and plate/plate measuring systems ME CC/CP

Brookfield Engineering Labs., Inc. Page 17 M/02-212 III.3.3 Mounting of the cooling device KE The optionally supplied cooling device “KE” m

Brookfield Engineering Labs., Inc. Page 18 M/02-212 IV. Environment, handling, cleaning and maintenance In this chapter you get information c

Brookfield Engineering Labs., Inc. Page 19 M/02-212 Check that any liquid does not penetrate into the housing (e.g. through the instrument con

Brookfield Engineering Labs., Inc. Page 2 M/02-212 Operating Manual for R/S Rheometer Version 1.10 E, valid for firmware version 4.02 All ri

Brookfield Engineering Labs., Inc. Page 20 M/02-212 V. Measuring Systems In this chapter you get information concerning use of the measuring s

Brookfield Engineering Labs., Inc. Page 21 M/02-212 Insert carefully the measuring bob into the measuring bob coupling. Pay attention to insert

Brookfield Engineering Labs., Inc. Page 22 M/02-212 Temperature range max.: 0°C ... +90°C. The cooling device “KE” is required to expand the t

Brookfield Engineering Labs., Inc. Page 23 M/02-212 To remove the measuring system after the measurement first open the measuring bob coupling

Brookfield Engineering Labs., Inc. Page 24 M/02-212 In order to avoid thread backlash, the height adjustment ring must be now obligatory turn t

Brookfield Engineering Labs., Inc. Page 25 M/02-212 VI. Operation and Menue System In the following chapter you will get overview on operatio

Brookfield Engineering Labs., Inc. Page 26 M/02-212 VI.1 Keyboard STBROOKFIELDOKSTART/STOP- back to parent menue- break- start of measurement

Brookfield Engineering Labs., Inc. Page 27 M/02-212 Key-function dependent to executed operation key operation Function of key example

Brookfield Engineering Labs., Inc. Page 28 M/02-212 VI.2 Menu System of R/S Rheometer T

Brookfield Engineering Labs., Inc. Page 29 M/02-212 Menu handling Because LCD display of R/S Rheometer cannot show simultaneously all menue i

Brookfield Engineering Labs., Inc. Page 3 M/02-212 CONTENTS I. GENERAL DESCRIPTION 5 I.1 Use of the Rheometer 5 I.2 Measuring Princ

Brookfield Engineering Labs., Inc. Page 30 M/02-212 • Selection of a program or a measuring system you want to edit in “Edit Program” and “Mea

Brookfield Engineering Labs., Inc. Page 31 M/02-212 Using and keys you can move cursor leftwards (rightwards). To process the nex

Brookfield Engineering Labs., Inc. Page 32 M/02-212 VI.5 Menue entries (MAIN menue) Menue entries (see Menue System in Chapter 6.2) may eit

Brookfield Engineering Labs., Inc. Page 33 M/02-212 At this point you either can start a measurement by pressing key, or return back t

Brookfield Engineering Labs., Inc. Page 34 M/02-212 After measurement, or after a break, the display field for Step indicates “END” or “BREA

Brookfield Engineering Labs., Inc. Page 35 M/02-212 If you have passed these points, before starting a measurement, the Rheometer will indicate

Brookfield Engineering Labs., Inc. Page 36 M/02-212 After measurement, or after a break, the display field for Step indicates “END” or “BREAK”.

Brookfield Engineering Labs., Inc. Page 37 M/02-212 VI.6 Menue entries in the Utilities-Menue Utilities menue, as its title presumes, conta

Brookfield Engineering Labs., Inc. Page 38 M/02-212 • measuring system to be used in the measurement • Number of steps • start and end valu

Brookfield Engineering Labs., Inc. Page 39 M/02-212 All free memory parts are marked as NEW. In order to avoid overwriting of already a

Brookfield Engineering Labs., Inc. Page 4 M/02-212 VI.7 Menu entries of the CONFIGURATION menu 44 VI.7.1 Configuration → Set output mode

Brookfield Engineering Labs., Inc. Page 40 M/02-212 For every step, there are the following inputs: Input Step Nr 1 Start[1/s]: 0010.00 End[

Brookfield Engineering Labs., Inc. Page 41 M/02-212 Saving of the Program: If you push key now, the Program will be saved. If you pu

Brookfield Engineering Labs., Inc. Page 42 M/02-212 After selection of the measuring system, you will be requested to input sequentially: its

Brookfield Engineering Labs., Inc. Page 43 M/02-212 If you have chosen the output device, you have to select the measuring series to transfer

Brookfield Engineering Labs., Inc. Page 44 M/02-212 VI.7 Menu entries of the CONFIGURATION menu The Entries: • Set output-mode sets output

Brookfield Engineering Labs., Inc. Page 45 M/02-212 b) for output to the serial interface (RS232), the receiving device (normally a PC) is set

Brookfield Engineering Labs., Inc. Page 46 M/02-212 After setting time and date you will be requested if you want to set clock for new time.

Brookfield Engineering Labs., Inc. Page 47 M/02-212 • Stopbits [Bit]: 1 or 2 Choose the requested parameter from the list of available v

Brookfield Engineering Labs., Inc. Page 48 M/02-212 3. The receiver is ready for reception and can (due to sufficient PC and memory capacity)

Brookfield Engineering Labs., Inc. Page 49 M/02-212 14. Start measurement at the Rheometer. Measurement points must now be seen as text at

Brookfield Engineering Labs., Inc. Page 5 M/02-212 I. General Description In this chapter you get general information concerning use and mea

Brookfield Engineering Labs., Inc. Page 50 M/02-212 VII. Measurements VII.1 Measuring in manual mode To carry out measurements in manual mo

Brookfield Engineering Labs., Inc. Page 51 M/02-212 Point to the fact that any substance or solvent do not ingress into measuring bob coupling

Brookfield Engineering Labs., Inc. Page 52 M/02-212 VIII. Technical data R/S Rheometer Dimensions 480 mm x 300 mm x 290 mm Weight 8 kg Nomina

Brookfield Engineering Labs., Inc. Page 53 M/02-212 FTK-CC Dimensions (Width x Height x Depth) 94 mm x 55 mm x 170 mm Weight 600 g Temperat

Brookfield Engineering Labs., Inc. Page 54 M/02-212 IX. Guarantee Brookfield Engineering Laboratories guarantees the faultless functioning of

Brookfield Engineering Labs., Inc. Page 55 M/02-212 APPENDIX A1 Data sheets of standard measuring systems Table Standard cylinder measuring

Brookfield Engineering Labs., Inc. Page 56 M/02-212 Table Double Gap cylinder measuring system according to DIN 53453 (consists of measuring

Brookfield Engineering Labs., Inc. Page 57 M/02-212 Table Cone/Plate measuring systems (DIN 53018) (consists of measuring cone and measuring de

Brookfield Engineering Labs., Inc. Page 58 M/02-212 A2 Error messages The R/S Rheometer is rather error resistive, when errors occur they are

Brookfield Engineering Labs., Inc. Page 59 M/02-212 Zero Calibration Error Cause: An impermissible high value was measured during carrying ou

Brookfield Engineering Labs., Inc. Page 6 M/02-212 II. System Configuration In this chapter you get information concerning system configuratio

Brookfield Engineering Labs., Inc. Page 60 M/02-212 BREAK: SPEED MAX Cause: Maximum speed exceeded during carrying out a measurement. a) You

Brookfield Engineering Labs., Inc. Page 61 M/02-212 A3 Pin-layout of the serial data cable The Rheometer is provided with a serial interface

Brookfield Engineering Labs., Inc. Page 62 M/02-212 A4 Requirements to the mains connecting cables The AC-adaptor unit of the R/S Rheometer en

Brookfield Engineering Labs., Inc. Page 63 M/02-212 - The mains plug must be 2-pin shockproof plug according to the Japanese Industrial Standa

Brookfield Engineering Labs., Inc. Page 64 M/02-212 German menue system of RC20 HAUPT-MenueEinzel-messungProgramm-MessungHilfsmittelKonfigurati

Brookfield Engineering Labs., Inc. Page 65 M/02-212 Index C cleaning, 18 computer system, 6, 8, 11 cooling device, 12 D Date, setting, 45 E el

Brookfield Engineering Labs., Inc. Page 7 M/02-212 R/S Rheometer main instrument (minimum configuration) O K S T PowerMain-Menue - Run Sin

Brookfield Engineering Labs., Inc. Page 8 M/02-212 II.2 Measuring Devices Measuring devices are not included in the main delivery volume of R

Brookfield Engineering Labs., Inc. Page 9 M/02-212 III. Instrument Installation In this chapter you will know how to prepare your R/S Rheomet